【Zigbee Bridge Pro】Firmware Changelog

eWeLink-Supported Device Release Logs SONOFF
1

V2.7.0

New Features:

  • Support for three new devices that have not yet been released. :wink:

Optimization:

  • Optimize the online/offline message transmission strategy, reduce device offline incidents.
  • Fix other bugs and enhance user experience.
V2.6.0

New Features:

  • Support remote unlocking of S60ZB after over-threshold protection is triggered.
  • Support for new devices that have not yet been released. :wink:

Optimization:

  • Optimize the RSSI reporting logic of sub-devices.
  • Fix other bugs and enhance user experience.
V2.5.0

New Features:

Certain features require app version V5.15.0+

  • Support setting SNZB-03 No motion detected for a duration as a scene trigger condition.
  • Support setting SNZB-06P No occupancy detected for a duration as a scene trigger condition.
  • Partial temperature and humidity sensors(SNZB-02P, SNZB-02D) support configuring report thresholds and report Interval to achieve faster reporting, or slower reporting to extend battery life.
  • Support ZBMINIR2 network LED indicator.

Optimization:

  • Fix other bugs and enhance user experience.
V2.4.0
  • Support daylight saving time.
  • Optimized TRV user experience.
V2.3.0

New Features:

  • Support adding ZBDongle-P and ZBDongle-E (flash router firmware).
  • Support temperature and humidity calibration for SNZB-02D(eWeLink App V5.12).
  • Support setting SNZB-03P No motion detected for a duration as a scene trigger condition(eWeLink App V5.13).
  • Support WiFi setting(eWeLink App V5.13).
  • Support using smart security mode as scene trigger conditions: smart security mode Armed, smart security mode Disarmed, smart security mode Armed cancelled(eWeLink App V5.13).

Optimization:

  • Optimize the online/offline message transmission strategy, reduce device offline incidents.
  • Fix other bugs and enhance user experience.
V2.2.0

New Features:

  • SONOFF NEW PRODUCT :wink: Supports Network indicator control and local scene.

Optimization:

  • Fix the issue of continuous rebooting of sub-device caused by power down during the sub-device OTA process, which may manifest as persistent offline status of the sub-device (low probability).
  • Fix the issue where resetting a multi-way switch sub-device during the process of adding it leads to an inability to add it subsequently (low probability).
  • Fix other bugs and enhance user experience.
V2.1.0

New Features:

  • Support synchronizing Zigbee Smart Water Valve to iHost.
  • Support SONOFF NEW PRODUCT :wink:.

Optimization:

  • Fix the issue of unable to reconnect to WiFi after a period of network disconnection.
  • Clear the list of sub-devices when added to a new eWeLink account.
  • Fix other bugs and enhance user experience.
V2.0.0

New Features:

  • Support Zigbee Smart Water Valve SWV.
  • Support Zigbee Smart Switch ZBMINIR2.

Optimization:

  • Automatically mute when switching smart security mode.
  • Optimize firmware stability and fix the low-probability crash issue of the gateway in large network scenarios.
  • Fix other bugs and enhance user experience.
V1.9.1

Optimization:

  • Fix the issue of local temperature and humidity scene failure.
V1.9.0

New Features:

  • Add two buzzer sounds: Alarm1 and Alarm2.
  • Add an buzzer prompt when disarm/arm the smart security.
  • Add Delay Arm feature in the samrt security.
  • Add Delay Alarm feature in the samrt security.
  • SONOFF TRV supports adjusting valve opening percentage and local scene.

Optimization:

  • Fix other bugs and enhance user experience.
V1.8.0

New Features:

  • Support sud-device RSSI

Optimization:

  • Fix WiFi reconnection issues and reduce WiFi offline.
4 Likes
2

Thank you for the information, when can we expect the release of ewelink 5.13?

3

eWeLink V5.13 for Android has been released on Google Play. Please check for available update, noting that due to a grayscale release, you may receive it a few days later.

As for iOS, the release will be around the end of the month, so please stay tuned.

Have a good day! :grinning:

4

and when will this option appear for other motion sensors and presence sensors??? Why can’t you update all devices at once???

6

If you are using Android, you can now update to version 5.13.0.

7

why is your post hidden? i cant read it

8

That post was mistakenly filtered by the AI spam detector.

9

There is no function “No motion detected for a certain period of time” as a scene trigger condition in version 5.13.0 for devices such as: SNZB-06P, SNZB-03.

1 Like
10

Changelog for v2.4.0 please

1 Like
11

What’s new in version 2.4.0?

1 Like
12

IMG_20250303_134030
IMG_20250303_1340301080×567 97 KB

1 Like
13

Changelog for v2.5.0 please

3 Likes
14

:grinning_face:We’ve updated the Changelog for v2.4.0 and v2.5.0.

1 Like
15

Changelog for v2.6.0 please

2 Likes
16

Hello, I’m considering to buy SNZB-06P to connect with a ZBbrdge-U.
The feature “No occupancy detected for a duration” means that I will be able to set conditions like “If no occupancy is detected for 1h turn off the lights” and “if no presence is detected for 3 hours change the valve settings to 16C”?
I’m sorry if the question looks stupid but I don’t want to buy something that will not be useful for me and I installed ewelink for the first time today.
Many thanks

17

Yes, you can set multiple scenes to perform different actions at different times after No occupancy detected.:grinning:

1 Like